PIC18F4450T-I/PT【PDF 113/241 页】IC PIC MCU FLASH 8KX16 44TQFP

收藏本站

您好，
买卖IC网欢迎您。
请登录
免费注册

买卖IC网

Sheet目录3872

109页 110页 111页 112页 [113页]114页 115页 116页 117页

dsPIC30F3010/3011

DS70141F-page 20

2010 Microchip Technology Inc.

2.2

Programmer’s Model

The programmer’s model is shown in Figure 2-1 and

consists of 16x16-bit working registers (W0 through

W15), 2x40-bit accumulators (ACCA and ACCB),

STATUS Register (SR), Data Table Page register

(TBLPAG), Program Space Visibility Page register

(PSVPAG), DO and REPEAT registers (DOSTART,

DOEND, DCOUNT and RCOUNT) and Program Coun-

ter (PC). The working registers can act as Data,

Address or Offset registers. All registers are memory

mapped. W0 acts as the W register for file register

addressing.

Some of these registers have a Shadow register asso-

ciated with each of them, as shown in Figure 2-1. The

Shadow register is used as a temporary holding regis-

ter and can transfer its contents to or from its host reg-

ister upon the occurrence of an event. None of the

Shadow registers are accessible directly. The following

rules apply for transfer of registers into and out of

shadows.

PUSH.S and POP.S

W0, W1, W2, W3, SR (DC, N, OV, Z and C bits

only) are transferred.

DO instruction

DOSTART, DOEND, DCOUNT shadows are

pushed on loop start, and popped on loop end.

When a byte operation is performed on a working reg-

ister, only the Least Significant Byte (LSB) of the target

mapped working registers is that both the Least and

Most Significant Bytes can be manipulated through

byte-wide data memory space accesses.

2.2.1

SOFTWARE STACK POINTER/

FRAME POINTER

The dsPIC DSC devices contain a software stack. W15

is the dedicated Software Stack Pointer, and will be

automatically modified by exception processing and

subroutine calls and returns. However, W15 can be ref-

erenced by any instruction in the same manner as all

other W registers. This simplifies the reading, writing

and manipulation of the Stack Pointer (e.g., creating

stack frames).

W15 is initialized to 0x0800 during a Reset. The user

may reprogram the SP during initialization to any

location within data space.

W14 has been dedicated as a Stack Frame Pointer as

defined by the LNK and ULNK instructions. However,

W14 can be referenced by any instruction in the same

manner as all other W registers.

2.2.2

STATUS REGISTER

The dsPIC DSC core has a 16-bit STATUS Register

(SR), the LSB of which is referred to as the SR Low

Byte (SRL) and the MSB as the SR High Byte (SRH).

See Figure 2-1 for SR layout.

SRL contains all the MCU ALU operation status flags

(including the Z bit), as well as the CPU Interrupt Prior-

ity Level status bits, IPL<2:0>, and the Repeat Active

status bit, RA. During exception processing, SRL is

concatenated with the MSB of the PC to form a

complete word value which is then stacked.

The upper byte of the SR register contains the DSP

adder/subtracter status bits, the DO Loop Active bit

(DA) and the Digit Carry (DC) status bit.

2.2.3

PROGRAM COUNTER

The Program Counter is 23 bits wide. Bit 0 is always

clear. Therefore, the PC can address up to 4M

instruction words.

Note:

In order to protect against misaligned

stack accesses, W15<0> is always clear.

发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

*型号	*数量	厂商	批号	封装

添加更多采购

采购需求

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

我的联系方式